CALL US : +919962060070

16 CHANNEL 12BIT PWM SERVO DRIVER

Price :
Rs.610.00/-
Quantity :  
  • 10 Units in Stock

DESCRIPTION

description:

• 16-Channel 12-bit PWM/servo driver with I2C interface
• I2C controlled PWM driver with a built in clock
• 5V compliant and can safely drive up to 6V outputs
• RoHS Compliant

The  16-Channel I2C Servo Controller is an I2C-bus controlled 16-channel LED controller optimized for LCD Red/Green/Blue/Amber (RGBA) color backlighting applications.

The PCA9685 is an I2C-bus controlled 16-channel LED controller optimized for Red/Green/Blue/Amber (RGBA) color backlighting applications. Each LED output has its own 12-bit resolution (4096 steps) fixed frequency individual PWM controller that operates at a programmable frequency from a typical of 24 Hz to 1526 Hz with a duty cycle that is adjustable from 0 % to 100 % to allow the LED to be set to a specific brightness value. All outputs are set to the same PWM frequency. Each LED output can be off or on (no PWM control), or set at its individual PWM controller value. The LED output driver is programmed to be either open-drain with a 25 mA current sink capability at 5 V or totem pole with a 25 mA sink, 10 mA source capability at 5 V. The PCA9685 operates with a supply voltage range of 2.3 V to 5.5 V and the inputs and outputs are 5.5 V tolerant. LEDs can be directly connected to the LED output (up to 25 mA, 5.5 V) or controlled with external drivers and a minimum amount of discrete components for larger current or higher voltage LEDs. The PCA9685 is in the new Fast-mode Plus (Fm+) family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated bus operation (up to 4000 pF). Although the PCA9635 and PCA9685 have many similar features, the PCA9685 has some unique features that make it more suitable for applications such as LCD or LED backlighting and Ambilight:

• The PCA9685 allows staggered LED output on and off times to minimize current surges. The on and off time delay is independently programmable for each of the 16 channels. This feature is not available in PCA9635.

• The PCA9685 has 4096 steps (12-bit PWM) of individual LED brightness control. The PCA9635 has only 256 steps (8-bit PWM).

 • When multiple LED controllers are incorporated in a system, the PWM pulse widths between multiple devices may differ if PCA9635s are used. The PCA9685 has a programmable prescaler to adjust the PWM pulse widths of multiple devices.

 • The PCA9685 has an external clock input pin that will accept user-supplied clock (50 MHz max.) in place of the internal 25 MHz oscillator. This feature allows synchronization of multiple devices. The PCA9635 does not have external clock input feature.

 • Like the PCA9635, PCA9685 also has a built-in oscillator for the PWM control. However, the frequency used for PWM control in the PCA9685 is adjustable from about 24 Hz to 1526 Hz as compared to the typical 97.6 kHz frequency of the PCA9635. This allows the use of PCA9685 with external power supply controllers. All bits are set at the same frequency.

• The Power-On Reset (POR) default state of LEDn output pins is LOW in the case of PCA9685. It is HIGH for PCA9635.

Features and benefits 

·         16 LED drivers. Each output programmable at:

·          Offu  Onu  Programmable LED brightnessu  Programmable LED turn-on time to help reduce EMI

·         1 MHz Fast-mode Plus compatible I2C-bus interface with 30 mA high drive capabilityn on SDA output for driving high capacitive buses  4096-step (12-bit) linear programmable brightness per LED output varying from fullyn off (default) to maximum brightness  LED output frequency (all LEDs) typically varies from 24 Hz to 1526 Hz (Default of 1Ehn in PRE_SCALE register results in a 200 Hz refresh rate with oscillator clock of 25 MHz.)  Sixteen totem pole outputs (sink 25 mA and source 10 mA at 5 V) with softwaren programmable open-drain LED outputs selection (default at totem pole). No input function.  Output state change programmable on the Acknowledge or the STOP Command ton update outputs byte-by-byte or all at the same time (default to ‘Change on STOP’).  Active LOW Output Enable (OE) input pin. LEDn outputs programmable to logic 1,n logic 0 (default at power-up) or ‘high-impedance’ when OE is HIGH.  6 hardware address pins allow 62 PCA9685 devices to be connected to the samen I 2C-bus  Toggling OE allows for hardware LED blinkingn  4 software programmable I2C-bus addresses (one LED All Call address and three LEDn Sub Call addresses) allow groups of devices to be addressed at the same time in any combination (for example, one register used for ‘All Call’ so that all the PCA9685s on the I2C-bus can be addressed at the same time and the second register used for three different addresses so that 1⁄ 3 of all devices on the bus can be addressed at the same time in a group). Software enable and disable for these I2C-bus address.  Software Reset feature (SWRST General Call) allows the device to be reset throughn the I2C-bus PCA9685 All information provided in this document is subject to legal disclaimers. N.V. 2015. All rights reserved. Product data sheet Rev. 4 — 16 April 2015 3 of 52 NXP Semiconductors PCA9685 16-channel, 12-bit PWM Fm+ I2C-bus LED controller  25 MHz typical internal oscillator requires no external componentsn  External 50 MHz (max.) clock inputn  Internal power-on resetn  Noise filter on SDA/SCL inputsn  Edge rate control on outputsn  No output glitches on power-upn  Supports hot insertionn  Low standby currentn  Operating power supply voltage range of 2.3 V to 5.5 Vn  5.5 V tolerant inputsn C operation°C to +85 °40 - n  ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM pern JESD22-A115 and 1000 V CDM per JESD22-C101  Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mAn  Packages offered: TSSOP28, HVQFN28n

 Applications 

·         RGB or RGBA LED drivers

·           LED status information

·         LED displaysn  LCD backlights

·          Keypad backlights for cellular phones or handheld devices